MASTER OF INDUSTRIAL AUTOMATION

DURATION : 3 MONTHS (240Hrs.)

PLC – 4 brands of PLC( Schneider, Allen Bradley, Siemens, Delta), SCADA, HMI, VFD, PLC Wiring and Control Panel Wiring and IIOT Concepts.
  1. Introduction to Electrical Engineering
  2. Applications used in industries
  3. Basic Concepts of Electricity
  4. Ohm’s Law
  1. Electrical Components and Symbols
  2. Electrical Circuit Analysis
  3. Relay logics and circuits
  1. Series and Parallel Circuits
  2. Voltage, Current, and Resistance
  3. Power and Energy in Electrical Systems
  1. Electrical machines(Motors and Types)
  2. Electrical Safety Practices
  1. Contactor – Latching/ Holding/ Retaining
  2. Timer – On delay/ OFF delay
  3. OLR, and SMPS
  4. Necessity of Motor Starters
  5. Direct online starters
  6. Motor – Forward Reversal with Interlocks
  7. Star-delta Starter
  1. Importance of Relay
  2. Relay
  3. Latching/ Holding/ Retaining
  4. Relay wiring with Logic gates
  5. Limit switch
  6. Reed switch
  7. Solenoid
  8. Actuators
  1. Overview
  2. Introduction to PLC
  3. Advantages of PLC Control Panel
  4. Architecture of PLC
  5. Working principle of PLC
  6.  
  1. PLC type and selection details
  2. Hardware configuration
  3. Software Explanation
  4. Communication details
  1. Online & Diagnostics
  2. Memory management
  3. Different types of Inputs and Outputs
  4. Concept of Digital I/O
  5. Concept of Analog I/O
  1. Concept of PLC scan cycle
  2. Maintenance and troubleshooting of PLC
  3. Selection of PLC
  4. Wiring of PLC
  5.  
  1. Source type input wiring
  2. Sink type input wiring
  3. Transistor type output wiring
  4. Relay type output wiring
  1. Various transmitters / sensors used in industrial applications
  2. Position sensor: Photo electric, proximity sensor, encoder)
  3. working principle, types selection guidelines
  4. Flow measurement, working principle, types, selection guidelines
  5. Pressure measurement, working principle, types, selection guidelines
  6. Load measurement, load cells
  7. Level measurement, working principle, types, selection guidelines
  8. Solenoid valves, control valves, smart transmitters
  9. Instrument transformers (CT,VT)
  10. Process control basics, closed & open loop control
  11. Process controllers (on-off, proportional, PID.
  1. Programming Language – Ladder diagram
  2. Device configuration – Start / Stop CPU
  3. Addressing details Digital, I/O’s
  4. Addressing details Analog, I/O’s
  5. Data Types – Bool, Integer, Real, Word, Dword
  6. Compile –Download, Upload program.
  1. Bit logic – NO, NC, NOT, SET, RESET, POSITIVE & NEGATIVE EDGE
  2. Timer – ON Delay, OFF Delay, Retentive Timer, Pulse Timer
  3. Counter – UP Counter, Down Counter, UPDOWN Counter
  4. Comparator – >, <, =
  5. Move Function
  1. Data type Conversion – ROUND, TRUNC, CEIL, FLOOR
  2. Math Functions – ADD, SUB, MUL, DIV, MOD, ABS, NEG
  3. Program control – CJ, CALL, LABEL, RETURN, MC, MCR
  1. Programming Language – Ladder diagram, FBD, STL
  2. Function Block, Functions – OB, FB, FC, DB
  3. Table, Cross reference
  4. Analog Configuration
  5. Analog signals 0v to 10v DC, 4mA to 20mA DC
  6. Adjusting gain & offset in A/D conversion
  7. Adjusting gain & offset in D/A conversion
  8. Scale function
  1. PID Configuration
  2. Real Time Clock – RTC
  3. High Speed Counter – HSC
  4. Pulse Train Output – PTO
  5. Libraries
  6. PDF conversion
  7. Real Time Applications
  1. Comparation of PLCs
  2. Reviews
  3. Discussion
  1. Programming Language – Ladder diagram
  2. Device configuration – Start / Stop CPU
  3. Addressing details Digital, I/O’s
  4. Addressing details Analog, I/O’s
  5. Data Types – Bool, Integer, Real, Word, Dword
  6. Compile –Download, Upload program.
  1. Bit logic – NO, NC, NOT, SET, RESET, POSITIVE & NEGATIVE EDGE
  2. Timer – ON Delay, OFF Delay, Retentive Timer, Pulse Timer
  3. Counter – UP Counter, Down Counter, UPDOWN Counter
  4. Comparator – >, <, =
  5. Move Function
  1. Data type Conversion – ROUND, TRUNC, CEIL, FLOOR
  2. Math Functions – ADD, SUB, MUL, DIV, MOD, ABS, NEG
  3. Program control – CJ, CALL, LABEL, RETURN, MC, MCR
  1. Programming Language – Ladder diagram, FBD, STL
  2. Function Block, Functions – OB, FB, FC, DB
  3. Table, Cross reference
  4. Analog Configuration
  5. Analog signals 0v to 10v DC, 4mA to 20mA DC
  6. Adjusting gain & offset in A/D conversion
  7. Adjusting gain & offset in D/A conversion
  8. Scale function
  1. PID Configuration
  2. Real Time Clock – RTC
  3. High Speed Counter – HSC
  4. Pulse Train Output – PTO
  5. Libraries
  6. PDF conversion
  7. Real Time Applications
  1. Comparation of PLCs
  2. Reviews
  3. Discussion
  1. Programming Language – Ladder diagram
  2. Device configuration – Start / Stop CPU
  3. Addressing details Digital, I/O’s
  4. Addressing details Analog, I/O’s
  5. Data Types – Bool, Integer, Real, Word, Dword
  6. Compile –Download, Upload program.
  1. Bit logic – NO, NC, NOT, SET, RESET, POSITIVE & NEGATIVE EDGE
  2. Timer – ON Delay, OFF Delay, Retentive Timer, Pulse Timer
  3. Counter – UP Counter, Down Counter, UPDOWN Counter
  4. Comparator – >, <, =
  5. Move Function
  1. Data type Conversion – ROUND, TRUNC, CEIL, FLOOR
  2. Math Functions – ADD, SUB, MUL, DIV, MOD, ABS, NEG
  3. Program control – CJ, CALL, LABEL, RETURN, MC, MCR
  1. Programming Language – Ladder diagram, FBD, STL
  2. Function Block, Functions – OB, FB, FC, DB
  3. Table, Cross reference
  4. Analog Configuration
  5. Analog signals 0v to 10v DC, 4mA to 20mA DC
  6. Adjusting gain & offset in A/D conversion
  7. Adjusting gain & offset in D/A conversion
  8. Scale function
  1. PID Configuration
  2. Real Time Clock – RTC
  3. High Speed Counter – HSC
  4. Pulse Train Output – PTO
  5. Libraries
  6. PDF conversion
  7. Real Time Applications
  1. Comparation of PLCs
  2. Reviews
  3. Discussion
  1. Programming Language – Ladder diagram
  2. Device configuration – Start / Stop CPU
  3. Addressing details Digital, I/O’s
  4. Addressing details Analog, I/O’s
  5. Data Types – Bool, Integer, Real, Word, Dword
  6. Compile –Download, Upload program.
  1. Bit logic – NO, NC, NOT, SET, RESET, POSITIVE & NEGATIVE EDGE
  2. Timer – ON Delay, OFF Delay, Retentive Timer, Pulse Timer
  3. Counter – UP Counter, Down Counter, UPDOWN Counter
  4. Comparator – >, <, =
  5. Move Function
  1. Data type Conversion – ROUND, TRUNC, CEIL, FLOOR
  2. Math Functions – ADD, SUB, MUL, DIV, MOD, ABS, NEG
  3. Program control – CJ, CALL, LABEL, RETURN, MC, MCR
  1. Programming Language – Ladder diagram, FBD, STL
  2. Function Block, Functions – OB, FB, FC, DB
  3. Table, Cross reference
  4. Analog Configuration
  5. Analog signals 0v to 10v DC, 4mA to 20mA DC
  6. Adjusting gain & offset in A/D conversion
  7. Adjusting gain & offset in D/A conversion
  8. Scale function
  1. PID Configuration
  2. Real Time Clock – RTC
  3. High Speed Counter – HSC
  4. Pulse Train Output – PTO
  5. Libraries
  6. PDF conversion
  7. Real Time Applications
  1. Comparation of PLCs
  2. Reviews
  3. Discussion
  1. Getting started with HMI
  2. Creating applications, creating tags
  3. Downloading /uploading programs.
  1. Creating alarm messages
  2. Communication with PLC
  3. Fault diagnostics
  1. New Window Creation & Linking.
  2. Button Creation and design.
  3. Output Design.
  1. Numeric Scaling and Demonstration.
  2. Multi-State Word Lamps and Switches.
  3. Alarm creation.
  1. Log Creation and Monitoring.
  2. Admin and User Role Creation and Security Assigned
  3. Trend Graph.
  1. Controlling field Devices.
  2. Tricks & Tips.
  1. Getting started with HMI
  2. Creating applications, creating tags
  3. Downloading /uploading programs.
  1. Creating alarm messages
  2. Communication with PLC
  3. Fault diagnostics
  1. New Window Creation & Linking.
  2. Button Creation and design.
  3. Output Design.
  1. Numeric Scaling and Demonstration.
  2. Multi-State Word Lamps and Switches.
  3. Alarm creation.
  1. Log Creation and Monitoring.
  2. Admin and User Role Creation and Security Assigned
  3. Trend Graph.
  1. Controlling field Devices.
  2. Tricks & Tips.
  1. Understanding the basic techniques of controlling an AC motor.
  2. Block Diagram of VFD
  3. How an AC drive is constructed, and how the various protection features work
  1. Operation of the AC drive.
  2. AC drive range and specification.
  3. Motor Nameplate – Drive
  4. Modes of Control
  5. V/F Control
  1. Speed & Torque
  2. Vector control
  3. Auto Tuning / ID Run
  4. Frequency Reference Setting
  5. Acceleration and De-Acceleration Control
  1. Forward and Reverse control
  2. Monitor / Display parameter
  3. Parameter Selection
  4. Parameter programming
  5. Set points
  1. Multi-speed control
  2. External speed control by Analog Input / Analog output
  3. Remote control
  4. Jogging concept
  5. Dynamic Braking
  1. Master slave concept
  2. Braking resistor
  3. Communication with PLC
  1. Introduction to HMI / SCADA
  2. Software Explanation
  3. Download and uploading the programs.
  1. IP address configuration
  2. Making New Project
  3. Features of SCADA
  1. Difference Between SCADA and HMI
  2. Difference Between SCADA and PLC
  3. Making and Editing New Graphic Display
  4.  
  1. Scada Tags – Memory, I/O, Discrete, Real, Integer, message
  2. Runtime, Development
  3. Animation
  4. Movement, Filling, Visibility, Blinking, Orientation, Height width,
  1. Tag creation
  2. Trend Details
  3. Real-time trend
  4. Historical trend
  1. Function Keys
  2. DDE / Suite link protocols
  3. Alarms and Events Details
  4. Security Control
  1. Introduction to switch gears & accessories
  2. Basics of control & power drawings
  1. General protection involved in panel
  2. Load management (connected load, running load, load factor)
  1. Indications (Ammeter, Volt Meter, PF & KW Meter etc.)
  2. Preparation of general arrangement diagrams, busbar sizing
  1. Electrical protection
  2. Preparation of power & control circuits
  3. General wiring guidelines / practices
  1. Maintenance & troubleshooting of control circuits in live panels
  2. Designing Power & Control Drawings through AutoCad
  1. REVIEW
  2. Activity Recap
  3. Role plays and Feedback
  4. Trainer Insights
  5. Closing Remark
  1. Function Keys
  2. DDE / Suite link protocols
  3. Alarms and Events Details
  4. Security Control
Scroll to Top